Free UAD Plug-ins with Every Apollo Purchase!

Save $300 on UAD Accelerators through 12/31! Find a dealer ›

Get up to 70% savings on UAD plug-ins storewide! Shop 12 Days of UAD ›

Hello world 4!

Hello world 5!

Save up to 85% on UAD plug-ins and bundles. Ends 12/4. Shop Cyber Monday ›

Save up to 85% on UAD plug-ins and bundles. Ends 12/4. Shop Cyber Monday ›

Gain Staging With Plug-Ins

Gain Staging With Plug‑Ins

What is Gain Staging? The Subtle Art of Signal Chains


For those of us who toiled over faders back when the earth was still cooling, the concept of gain staging was fairly easy to grasp. Each separate box was a link in the audio chain, visibly connected via patch cables, and analog distortion was easy to hear and identify. In today’s all-digital, in-the-box world, it’s not that simple. Signal paths can be unconventional and convoluted, and digital distortion can be subtle and sneaky.


But while the dawn of the DAW has fundamentally changed the way we make records, proper gain staging is no less critical to good recording. The user-friendly, forgiving design of computer audio programs can make it all too easy to overlook a poorly-thought-out signal chain, and the results can sneak up and bite you.

The concept of gain staging is no less important in your DAW than in a fully analog recording environment.

Everything to Gain

An audio signal in a typical recording chain might travel through a multitude of devices and gain stages. Each of these devices, whether analog hardware or software plug-ins, needs to receive an optimal signal level at its input; not enough level can add noise, while too much can cause clipping and distortion. Aside from channel inserts, most plug-ins’ input levels are controlled via effects sends, as well as the plug-in’s own input level control. Matching effects send level with the plug-in’s input level is the first key to proper gain staging. Sending too low a level to the effects bus and then turning the plug-in’s input level up to compensate will result in a noisier signal. Conversely, sending too hot a signal to the effects bus will result in a distorted signal.


Other than channel inserts, most plug-ins’ input levels are controlled via the mixer’s effects send, as well as the plug-in’s own input level control. Matching the mixer’s send level with the plug-in’s input level is key to proper gain structure. Sending too low a level to the effects buss and then turning up the plug-in’s input level to compensate will result in a noisier signal. Conversely, sending too hot an effects send level and then turning down the plug-in’s input level will result in a distorted signal.

"If your signal level is noticeably higher or lower when you bypass the device, it’s a good idea to examine your gain structure"

Generally speaking, unity gain is the goal. With some exceptions (notably compressors and other dynamics processors), a good rule of thumb is to try and achieve the same peak level whether a plug-in is inserted into the signal chain or not. If your signal level is noticeably higher or lower when you bypass the device, it’s a good idea to examine your gain structure.

A typical audio signal might travel through a multitude of gain stages. Whether analog hardware or software plug-ins, each device needs to receive an optimal signal level at its input.

Getting Right with Gain

Clipping can be particularly problematic in the digital domain. Raise the input signal going to an analog device, and distortion will gradually rise until it clips. Digital circuitry has no such safety zone — a single dB too high will take your signal from clean to clipped.


Unlike analog clipping, this digital clipping can be difficult to hear, particularly when it’s just one element of a dynamic mix. If the clipping goes undetected, the digital information for that sound is permanently corrupted, even if the levels are brought back down later in the mix. The distortion from digital clipping can have a subtle but undesirable effect on the sonic quality of your track, usually in the form of barely perceptible levels of a brittle, harsh digital sheen that can fatigue your listeners.


Even a relatively small bit of gain from certain plug-ins — for example, a high-pass filter — can boost peaks and transients significantly. Don’t depend on your meters to alert you to these, either. In most DAW setups, plug-in inserts occur pre-fader, so even if you keep the levels of your channel strips below clipping, distortion within a given plug-in may not show up if the level was brought back down further along the signal chain. Your ears are your most important tools. Solo each device and listen.


What to Watch For

Different types of signal processors will affect overall gain structure differently, and some are easier than others to work with. With a reverb like the EMT 250 Classic Electronic Reverberator, distortion is typically not that hard to hear. But the "soft" nature of some reverb algorithms can mask other artifacts, including noise resulting from too low an effect send level.


Multiband EQ can be particularly nefarious, especially when it comes to peaks and transients. With modern multiband EQ plug-ins like the Neve 88RS Channel Strip, it’s easy to inadvertently overlap a range of frequencies in two different bands, and the cumulative boost can result in clipping.


Compression and dynamics processing present a different set of challenges, and an in-depth discussion on how they affect the signal chain is a subject for an article of its own. But briefly, it’s important to pay attention to a compressor’s attack and gain settings, as these controls work in tandem and can have a major impact on the level of signal coming out of your compressor.

With EQ/channel strip plug-ins like the UAD Neve 88RS, you can accidentally clip your signal by boosting at the same frequency of two different bands.

Get to Know Your Plug-Ins

Different devices have unique ways of handling gain and clipping. Just as vintage guitars and amps have their own sonic character, so too do hardware signal processors and the plug-ins that model them. Understanding the clipping characteristics and headroom potential of your plug-ins and how they might perform in different places in your signal chain is as important as knowing which vintage synth would suit the chorus of a certain song or which amp would sound best for a rhythm guitar track.


In the analog era, engineers would test each new box by running a sine wave through it and looking at the signal on an oscilloscope. They could see where each device would clip at specific frequencies, what kind of distortion would occur, and other characteristics that helped to map out the device’s optimal gain settings and place in the chain.

"It’s important to understand the clipping characteristics and headroom potential of your plug-ins and how they might perform in different places in your signal chain"

You can easily do the same thing with plug-ins. Open an oscilloscope or frequency display in your DAW, set the plug-in’s input level (and output, if it has one) to unity gain, and send a sine wave through the device. Watch the output as you gradually raise the send level.


Of course, the geek factor of testing with sine waves is no substitute for listening. Many tracks in a mix will have multiple plug-ins inserted in their signal path. Don’t forget to listen to each one individually, rather than the results of several effects combined.


Like Watching Paint Dry

If you’ve gotten this far you’ve probably figured out that gain structure is neither exciting nor creative. But it’s one of those necessary facts of recording life, and ignoring it is not an option. The more familiar you are with gain staging and how these concepts apply to your particular equipment, the less time you’ll have to spend optimizing levels with a room full of antsy musicians waiting record.

— Daniel Keller

Read More